Faça parte da RUCKUS Technical Family

ICX 7250 9.0.10 config parsing error at boot

We have a small number of remaining ICX 7250s which are running 8.0.95. They are mostly in environments that require a quiet switch (albeit not fanless) with more than 12 POE ports, and I don't really have budget to replace them.I upgraded one of our spares to 9.0.10j_cd7T213 to play around. There are the usual oddities I've also seen with version 10 (prompting for a username on "enable" seems like a behavior change specifically designed to enrage experienced network engineers...) but only one thing I really found concerning. By policy we disable all management except SSH and serial console on all network devices - it's non-negotiable.Booting our standard configuration on the 7250 with 9.0.10 yields this, just before the console first prompts for login:Config parsing complete: 0,43 percent time: 00:10 parsed: [ver 09.0.10j_cd7T213]Error - Config send failedError [1 ui_common_send: Not able to apply - itc error please try again] parsing line: [no web-management https]show run from a privileged exec does show the "no web-management https" statement, and it does not appear the switch is actually listening on port 443, but, more disturbingly, if I then interactively reconfigure the switch with "web-management https" and then "no web-management https" it throws the same "Config send failed" error and rejects all subsequent configuration statements.Is this the kind of thing to expect from 9.0.10? I haven't tried downgrading a switch from 9 or 10 to 8, but maybe this is the time...

[Ultimate Supreme] CBGHK attapoll referral code $20 ;TRY NOW

Use the latest attapoll referral code [CBGHK] for free and get $0,50.Some people have also confirmed of getting $20 sometime while using the referral code CBGHK.I started using AttaPoll recently, and it's been a surprisingly easy way to make a bit of extra cash during my downtime. The surveys are short and straightforward—perfect for when I’m commuting or just relaxing. When I signed up, I used the referral code [CBGHK], which gave me a small bonus after I finished my first survey.

how to obtain and load SPR codes

I have purchased an ICX-7450-48P from amazon, both pri and sec flash is showing SPS080300h.binHow do I get it to reload SPR codes, where can I find the codes? Obrigado

Temperature sensors (AIR OUTLET NEAR PSU) on Icx7250-48p,

Hello,Can someone just explain where is the position of this temperature sensor exactly.I understand the one that is call "MGMT THERMAL PLANE", but this is not clear for me about the air outlet.Is it wherechassis pierced with a small hole above the PSU ? because there is no fan at this place, so it's just natural convection outtake ?At summer time, my icx7250 switch frequently to the high cpu fan speed because the temperature is two high.The temperature low threshold seems quite low : 41°c to toggle two high speed, but only 34° to come back to low speed.Thanks, Laurent.

Having an issue with Unleashed R650s over multiple floors

Having an issue setting up Unleashed R650s on multiple floors. So it's a four story office building and each floor has its own Cisco switch(es). IT is on the third floor so that's where I have the Master unit. All the APs on the third floor connected just fine no issues. The issues started when I tried setting up on the other floors. The APs would power up, the CTL light would go solid but then nothing further would happen. As a fix I tried having the APs for the other floors turn on and connect for the first time on the third floor. Once I saw them in the Unleashed admin portal, I then moved the APs to where they needed to be. It's at that point they show up as disconnected in the admin portal. However, they show with lights on for Air and 2.4ghz/5ghz lights, and when I connect my phone to wifi the 5ghz light goes green. But they continue to show as disconnected in the admin portal. What other troubleshooting steps should I take? Thanks in advance!

H510 standalone firmware independent of ZD

I have and H510 I use as a travel standalone AP. It recently connected to a ZD on a job site and I would like to get it back to a standalone.I completed a hard reset on the side of the device. I finally figured how to get back into it and I'm connected to it via ethernet cable in LAN4. It's on version200.15.6.112.52.I have tried to install H510_114.0.0.0.1360.bl7 when prompted to select image file locally but receive "This does not seem to be a valid upgrade image. Please try another file". I have also tried other files to receive the same notification after attempted uploading of bl7.Appreciate any assistance to get this back to an AP independent of Unleashed.